Making precast concrete structures safer

Published 26 August 2008

Precast concrete helps builders save time and money, and also increase buildings’ durability; new research aims to make them better able to withstand earthquakes

Practice, practice, practice. The structure, which resembled a parking garage, went through a series of earthquake jolts as powerful as magnitude 8.0. The one-million pound precast concrete structure had the largest footprint of any structure ever tested on a shake table in the United States. The earthquake tests were conducted at the University of California San Diego Jacobs School of Engineering’s Englekirk Structural Engineering Center, which is about eight miles east of the university’s main campus. The goal of the project was to test the seismic response of precast concrete floor systems used in structures such as parking garages, college dormitories, hotels, stadiums, prisons and office buildings.

One of the purposes of our research is to develop better designs for precast concrete buildings,” said Jose Restrepo, co principal investigator of the project and a structural engineering professor at UC San Diego’s Jacobs School of Engineering. “The results of our research have been tremendous.”

Precast concrete, which is built in pieces and then put together to construct buildings, has been a breakthrough in the industry in terms of saving time, money and increasing durability. While precast concrete has proven to be a robust design material for structures, researchers are working to provide the industry with new methods of connecting these pieces more efficiently. “This is really important to our industry because we’ll be able to develop structures that can resist nature’s most difficult loads, including earthquakes,” said Tom D’Arcy, spokesman for the Precast/Prestressed Institute and chairman of the Consulting Engineers Group.

The $2.3 million research project is a collaboration among UC San Diego, the University of Arizona, and Lehigh University, and is funded by the Precast/Prestressed Concrete Institute and its member companies and organizations, the National Science Foundation, the Charles Pankow Foundation, and the network for earthquake Engineering Simulation (NEES).

During the tests, the researchers simulated earthquakes for different regions of the country, including Berkeley, California; Knoxville, Tennessee; and Seattle, Washington. “We conducted tests from lower seismicity all the way to higher seismicity and shook the building stronger and stronger each time with a higher intensity,” Restrepo said. The results of the research are expected to be implemented into building codes across the United States within the next few years. The researchers and industry leaders hope that this project and others like it will help prevent the future failure of buildings, much like what happened during the 6.7 magnitude earthquake in Northridge, California in 1994, with the collapse of several precast parking structures. “Since that time, we have been working to come up with designs that will make these structures survive a Northridge earthquake or stronger,” said Robert Fleischman, principal investigator of the project and a civil engineering professor at the University of Arizona.

Before the testing, the researchers performed computer simulations to help design the three-story structure and to determine where sensors should be placed on it. The data recorded by the sensors were used to take measurements of certain physical phenomena on the structure such as displacements, strains, and accelerations caused by the shaking; and to estimate forces in the structure. The data collected will also explain behavior of the structure during and after jolts,and will be used to compare directly to the simulations to either validate or adjust the computer models.

The use of these sensors, along with the computer simulation, may help lower costs of future seismic tests. “We are only able to perform physical experiments on that one structure, but if we can show that our models capture important response properly, we can run hundreds of earthquake simulations a year for the cost of a graduate student, a fast computer and a software license, which, at around $50,000, is substantially less than the costs of these kinds of tests,” Fleischman said, adding that the researchers hope to have their first formal report on the seismic tests completed by early 2009.

The $9 million Englekirk shake table is one of 15 earthquake testing facilities for NEES. The UCSD-NEES shake table, the largest in the United States and the only outdoor shake table in the world, is ideally suited for testing tall, full-scale buildings. “The Englekirk Center is very important to the research community and to the industry because it has an outdoor environment where we can perform large scale tests that can’t be done anywhere else in the world,” Restrepo said.